littre пишет:Отправил эти команды, на обе в ответ лаконично говорит ОК
видимо я какое то другое устройство нашел, а не gsm модем)))
возможно с помощью этого можно самим железом телефона управлять
Я тестировал это только на самом телефоне. Там ответ на первый и будет просто OK а на второй будет уже длинный ответ с текстом ussd ответа.
Возможно и правда это просто нашлось другое устройство.
Кстати я вроде где-то видел расширенный набор AT команд для gsm модемов. Вот документированный список, но их на самом деле больше:
AT commands set for Nokia GSM and WCDMA products
Call control
Command Description
ATA Answer command
ATD Dial command
ATH Hang up call
ATL Monitor speaker loudness
ATM Monitor speaker mode
ATO Go on-line
ATP Set pulse dial as default
ATT Set tone dial as default
AT+CSTA Select type of address
AT+CRC Cellular result codes
Data card control commands
Command Description
ATI Identification
ATS Select an S-register
ATZ Recall stored profile
AT&F Restore factory settings
AT&V View active configuration
AT&W Store parameters in given profile
AT&Y Select Set as powerup option
AT+CLCK Facility lock command
AT+COLP Connected line identification presentation
AT+GCAP Request complete capabilities list
AT+GMI Request manufacturer identification
AT+GMM Request model identification
AT+GMR Request revision identification
AT+GSN Request product serial number identification (IMEI)
Phone control commands
Command Description
AT+CBC Battery charge
AT+CGMI Request manufacturer identification
AT+CGMM Request model identification
AT+CGMR Request revision identification
AT+CGSN Request product serial number identification
AT+CMEE Report mobile equipment error
AT+CPAS Phone activity status
AT+CPBF Find phone book entries
AT+CPBR Read phone book entry
AT+CPBS Select phone book memory storage
AT+CPBW Write phone book entry
AT+CSCS Select TE character set
AT+CSQ Signal quality
Computer data card interface commands
Command Description
ATE Command Echo
ATQ Result code suppression
ATV Define response format
ATX Response range selection
AT&C Define DCD usage
AT&D Define DTR usage
AT&K Select flow control
AT&Q Define communications mode option
AT&S Define DSR option
AT+ICF DTE-DCE character framing
AT+IFC DTE-DCE Local flow control
AT+IPR Fixed DTE rate
Service
Command Description
AT+CLIP Calling line identification presentation
AT+CR Service reporting control
AT+DR Data compression reporting
AT+ILRR DTE-DCE local rate reporting
Network communication parameter commands
Command Description
ATB Communications standard option
AT+CBST Select bearer service type
AT+CEER Extended error report
AT+CRLP Radio link protocol
AT+DS Data compression
Miscellaneous commands
Command Description
A/ Re-execute command line
AT? Command help
AT*C Start SMS interpreter
AT*T Enter SMS block mode protocol
AT*V Activate V.25bis mode
AT*NOKIATEST Test command
AT+CESP Enter SMS block mode protocol
SMS commands
SMS text mode
Command Description
AT+CSMS Select message service
AT+CPMS Preferred message storage
AT+CMGF Message format
AT+CSCA Service centre address
AT+CSMP Set text mode parameters
AT+CSDH Show text mode parameters
AT+CSCB Select cell broadcast message types
AT+CSAS Save settings
AT+CRES Restore settings
AT+CNMI New message indications to TE
AT+CMGL List messages
AT+CMGR Read message
AT+CMGS Send message
AT+CMSS Send message from storage
AT+CMGW Write message to memory
AT+CMGD Delete message
SMS PDU ode
Command Description
AT+CMGL List Messages
AT+CMGR Read message
AT+CMGS Send message
AT+CMGW Write message to memory
